| Sizes | | Final Trim Size | | Finished label cut according to your order (cuting lines). | | Full Bleed Size | | Your artwork file has to consist of two pages: first with your job in full bleed size and second with the cutting lines. | | Bleed | The artwork area that goes beyond the trim lines/score marks The size of the bleed should be 2 mm on each side.
In case of shapes other than rectangular do not fill with the background whole working area - only this 2mm bleed. Rest of the working area leave white.
| | Single Label | - labels can take on any shape
- Important elements should be placed at least 3 mm from the designed trim line.
- Do not design frames, borders, etc. near the cut line (leave at least 5 mm). It is essential to allow some leeway for trim movement, otherwise printed pieces may not look aesthetically pleasing.
| | Cutting Template | Cutting TemplateCutting line should not have roundings with radius smaller than:
- 3 mm - for 3D dome stickers
- 6 mm - for magnetic labels
Cutting line should be drawn with a single closed curve.
Project cutting lines with a hairline (width) in black colour (100%K).
In order to save cutting time:
- use straight lines instead of curves wherever it is possible,
- use only as few nodes as needed to draw the curve,
- cutting lines cannot overlap.
When projecting the cutting line try to avoid placing its beginning and ending points on the curve - it looks best when you put them in the middle of the straight line.
3D Dome Stickers:
- Due to the physico-chemical properties of the polyurethane resin, please prepare 3D Stickers of regular shapes - circles, ellipses, rectangles, squares, polygons or other regular shapes with rounded corners.
- Irregular shapes, sharp corners, concave shapes, etc. increase the workload, so increase the price stickers and extend the date of realization. In such cases, we will have to increase the price i extend the deadline for this kind of order!
After projecting the cutting lines, please save them on the separate page within your artwork file or in second, separate file.
PLEASE NOTE!
Trim lines should consist of a minimum number of vertices necessary for the creation of a required shape and ungrounded increase in curve vertices results in slowing down the plotter operation.
If it turns out that the curve complexity causes excessively slow plotter operation, the job will be stopped due to an incorrectly prepared file. |
|
| Graphics | | Colour Model | Prepare your artwork in CMYK model (except for artwork with additional colour). If your artwork contains halftone images (textures, photos), convert it also to CMYK.
Using different colour spaces or colour models in one document (e.g. CMYK and RGB) leads to incorrect colour rendering and is not covered by warranty.
When defining your own CMYK colours, the total tonal value at one point should not exceed 300% (for one-side coated cards, 200% should not be exceeded on the uncoated side, and, in particular, placing saturated solids in the same place on the face and back of the printed piece should be avoided). If this parameter is exceeded, no warranty claims shall be accepted. (The above mentioned rule means, for example, that black cannot consist of four 100% components.)
For printed materials to be laminated, the total tonal value at one point should not exceed 250%.
For 3D stickers, total CMYK tonal values may not exceed 200% coverage!
| | Rich Black | | In order to obtain rich saturated black use 33%C 33%M 33%Y 100%K. | | Gray Large Solid | | If you want the background to be grey, compose it of the 'K' component only, without using the remaining 'CMY' colours. | | Tone Gradation | To avoid visual bands, add some noise to your gradation.  | | Optimum Resolution | | Optimum resolution for bitmaps (graphics, photos) is 300dpi.
| | Layout | Please set texts and any important information (graphics, photos) at least 3mm from the edge of a page (in actual trim size) and from scores for folding.
In case of saving your artwork as CDR file, please group all the objects and convert all fonts to curves/paths.
In your file please define your artwork size in accordance with above mentioned size and place your artwork centrally on a page.
If you save as EPS file the artwork which has no background (white), please frame it to above mentioned size.
Due to cutting tolerance some slight movements in relation to artwork edges may occur.
For that reason we recommend to avoid those kinds of framing where such distortions could be visible.
By default utilities are reversed "Head to Head". |
|
| Saving to File | | File Formats | | Plik do druku: | Preferred: PDF
Accepted: CDR,EPS, TIFF, JPG. For jobs delivered in these formats, an extra fee of PLN 3.50 is charged for prepress file preparation.
| | Cutting Template: | Preferred: PDF
Accepted: CDR,EPS. For jobs delivered in these formats, an extra fee of PLN 3.50 is charged for prepress file preparation.
|
Files must be zipped before they can be attached to the job. | | Additional Information | Please remember: if the artwork contains text, it must be outlined before saving or the file must be supplied with the fonts that were used in the artwork.
When saving to a PDF file, set the graphics to high resolution. Save your PDF files as PDF/X, PDF/X-1a or PDF 1.3 (Acrobat 4.0.)
Save PostScript files as composite files.
For complex projects with multiple layers, overlapping graphics, shadows, transparencies etc., as far as possible, flatten to a single background image, retaining texts, logos, lines and other important elements of the project in the vector form only. In particular, this problem concerns CorelDRAW X4, where in extreme cases, despite a good-looking PDF file, the printout may contains errors.
PLEASE NOTE!
Please, don't leave (save) planned cutting lines in the printing file!
|
|
| Additional Information | | | Please keep in mind that due to differences in printing technology and colour presentation, some differences in colours may occur also when compared to inkjet printouts or colours displayed on a computer screen. |
|
|
|
|
|
