| Sizes | | Final Trim Size | | Available trim sizes: A4 210 x 297 mm, A5 148 x 210 mm. | | Full Bleed Size | Please set your artwork to the exact correct size as follows: A4 214 x 301 mm, A5 152 x 214 mm - (full bleed size.)
PLEASE NOTE!
Even if your artwork does not have any background colours or design elements extended to the bleed area, always use the full bleed size. To ensure the correct size of your artwork, mark it out with a rectangle at the lowest layer (without any outline or filling), or for a bitmap, frame the artwork appropriately.
| | Bleed | Artwork background and all objects adjoining the edge of the final piece must be extended over the edges to the bleed. The size of bleed for this artwork should be 2 mm at each side. |
|
| Graphics | | Colour Model | Please provide your artwork in CMY K palette (pdf).
To achieve this in Corel, you should:
- In Colour Management (the Tools tab):
- For older versions, select Settings - Optimized for Professional Output (check that the general profile is set to colour printing).
- For newer versions, select Europe Prepress (check that the ISO Coated v.2 profile is set).
In both cases, Coated FOGRA39 profile, available from the Adobe website, can be used (recommended).
- In Publish to PDF, select Prepress Settings. For Prepress Settings in the Prepress Settings tab, uncheck all options and:
- For older versions, in the Advanced tab, check that colour management is set to CMYK and that the ICC profile for the colour output press is activated.
- For newer versions, in the Colour tab, select Output colour as CMYK and do not apply the colour profile.
When defining your own CMYK colours, the total tonal value at one point should not exceed 300% (for one-side coated cards, 200% should not be exceeded on the uncoated side, and, in particular, placing saturated solids in the same place on the face and back of the printed piece should be avoided). If this parameter is exceeded, no warranty claims shall be accepted. (The above mentioned rule means, for example, that black cannot consist of four 100% components.)
For printed materials to be laminated, the total tonal value at one point should not exceed 250%.
Using ICC ISO Coated v.2_300 profile is recommended, whenever possible, as it limits color components to 300%, unlike ISO Coated v.2 profile, which allows components to achieve up to 330%. | | Rich Black | | To achieve solid, saturated black, use black composed of the following components: 60%C 55%M 50%Y 100%K. | | Gray Large Solid | | Grey solid should be created using all CMYK components. Values: C:50% M:40% Y:40% K:22% | | Tone Gradation | To avoid visual bands, add some noise to your gradation. | | Optimum Resolution | | Optimum resolution for bitmaps (graphics, photos) is 300dpi.
| | Layout | Please set texts and any important information (graphics, photos, text) at least 3mm from the edge of a page (in actual trim size) and from scores for folding.
When rotating your artwork by -90 degrees please check whether the bitmaps rotate correctly.
In case of saving your artwork as CDR file, please group all the objects and convert all fonts to curves / paths.
In your file please define your artwork size in accordance with above mentioned size and place your artwork centrally on a page.
If you save as EPS file the artwork which has no background (white), please frame it to above mentioned size.
Due to cutting tolerance some slight movements in relation to artwork edges may occur. For that reason we recommend to avoid those kinds of framing where such distortions could be visible.
By default utilities are reversed "Head to Head" |
|
| Saving to File | | File Formats | Preferred: PDF
Accepted: CDR, TIFF, JPG (not recommended).
Please note: In case of INDESIGN software, we accept only PostScript files. Otherwise, please use the Comment section to inform us: "Attention: InDesign file. Convert to PS, please". PDF, EPS, PRN
Accepted: CDR, TIFF, JPG (unrecommended).
We are adding the extra fee 3,5 pln, for the preparation of the pdf file to orders with jpg files.
Please note: In case of INDESIGN software, we accept only PostScript files. Otherwise, please use the Comment section to inform us: „Attention: InDesign file. Convert to PS, please"
| | Additional Information | When saving to a PDF file, set the graphics to high resolution. Save your PDF files as PDF/X, PDF/X-1a or PDF 1.3 (Acrobat 4.0.)
If you have text in your artwork please remember to convert it to curves / paths or attach used fonts to your file (refers only to PDF files).
Don't convert texts to bitmaps!!!
If your artwork consists of more than one page, please save all pages in a single file. If the chosen file format does not allow for saving all pages in one file, please save them in two separate files named face and reverse. (projekt_awers.tiff, projekt_rewers.tiff)
In case of preparing separate files for finishing, please include in their name information, which sides concern.
If you send more than one file, please send them in ZIP format if possible.
In case of TIFF files please save them as single layer files, with no additional channels. For complex projects with multiple layers, overlapping graphics, shadows, transparencies etc., as far as possible, flatten to a single background image, retaining texts, logos, lines and other important elements of the project in the vector form only. In particular, this problem concerns CorelDRAW X4, where in extreme cases, despite a good-looking PDF file, the printout may contains errors. |
|
| Additional Information | | | Please keep in mind that due to differences in printing technology and colour presentation, some differences in colours may occur also when compared to inkjet printouts or colours displayed on a computer screen. |
|
|
|
|
|
